Intelligent 500mA Smart Charger for 4.8V-12V NiMH NiCd Race RC Batteries Vapex

In stock
SKU
VTE500P
£10.95
New Design Charges 4-10 cell NiCd or NiMH battery packs. (4.8V - 12V) Delta-Peak microprocessor controlled charging, switches to trickle charge once pack is charged. LED shows when charging & when complete. UK 3-pin mains plug

Smart & Fast Charger for 4~10 Cells Battery Packs


This Charger is designed to charge Nickel-Metal Hydride (NiMH) or Nickel Cadmium (NiCd) 4~10 Cells battery packs with the Standard Tamiya Connector. This is a microprocessor controlled Smart Charger, which can automatically distinguish 4~10 cell packs. Automatically cut-off once charging is complete. Easy to use, no manual adjustment required. By using different adaptors, this charger can be used to charge battery packs with Futaba, JR, Mini-Tamiya, XT60, EC5 connectors etc.


Input Rated Voltage & Line Frequency: 240VAC 50Hz
Rated Voltage: DC18.0V+-5%
Rated Current: DC500mA
Rated Cells Pack: 4~10 Cells
No Load Voltage: DC23.5V Max
Trickle Current: 60mA Max
Short Circuit & Reverse Polarity
Protection included


Features:

 

    This charger is fitted with a standard tamiya male connector (male housing with female contacts inside) we can supply adapters for just about any other connector, just contact us if you cannot find the adapter you need.

  • Recharges 4~10 cell battery packs 
  • Ni-MH/Ni-Cd batteries with Standard Tamiya connector 
  • Microprocessor-control System (For protection and safety). 
  • Battery life is protected by –dV detection and also timer protection. 
  • LED display for Rapid charge/trickle charge 
  • Red LED- rapid charge 
  • Green LED- Fully Charged & trickle charge 
  • Flash Red and Green LED- short 
  • Flash Red LED: Reverse polarity or Wrong Battery 
  • Safety features:  -dV cut-off function 

OPERATION INSTRUCTIONS :

  1. Connect 1 pack of 4~10 cells with Tamiya connector to the charger. (using adapter if necessary) 
  2. If using an adapter, ensure that the polarity of the contacts is correct. 
  3. Plug charger into mains socket. 
  4. The status LED will glow Red when the batteries are receiving charge. After charge is completed, the status LED will change green to indicate that the charge is completed and batteries are ready for use. Once the status LED is Green, the charge switches to trickle mode to keep the batteries at full. 
  5. Unplug the charger and remove the batteries from the charger when not in use. 

Mechanical Specification:

  1. Plastic Case: 70×40×28mm 
  2. Output DC Cord: 26AGW×1500mm×2C 

Environmental
Operating temperature: 0~35℃
Short Circuit Protection: 20mA


Charging Table

SizeInputOutput current
VoltageCurrent
4 cells16V 240mA 500mA 
5 cells 16V280mA 500mA 
6 cells 16V396mA 500mA 
7 cells 16V423mA  500mA 
8 cells 16V450mA  500mA 
9 cells 16V480mA  500mA 
10 cells 16V500mA  500mA 

 

Charging time

SizeCharging currentCharging Time
800mAh500mA1.5 hours
1600mAh500mA3.3 hours
2000mAh500mA4.7 hours
2600mAh500mA6 hours
3000mAh500mA6.5 hours
3300mAh500mA7 hours
3700mAh500mA8 hours
4300mAh500mA9 hours
4600mAh500mA10 hours
5000mAh500mA11 hours

 

*Charge time will vary depending upon the brand,
capacity and condition of batteries being
charged.

Important Safety Instructions

  1. Before charging, read instruction. 
  2. This charger is intended for use with Nickel-Cadmium and Nickel-metal-hydride rechargeable batteries only. Attempting to charge other types of batteries may cause personal injury and damage to the charger. 
  3. Recharge only one type of battery (Ni-Cd or Ni-MH) at each time. 
  4. Do not expose charger to rain or moisture. For indoor use only. 
  5. Remove from mains when not in use. 
  6. Never use an extension cord or any attachment not recommended by manufacturer, otherwise this may result in a risk of fire, electric shock or injury to persons. 
  7. Do not operate the charger if it has been subjected to shock or damage. Take it to a qualified serviceman for repair. 
  8. Do not disassemble the charger. Incorrect reassembly may result in a risk of electric shock or fire. 
  9. Unplug the charger from outlet before attempting any maintenance of cleaning.

Note: European Customers will receive EU PLUG unless they notify us that they require UK PLUG

More Information
SKU VTE500P
Colour Black
Gift Type Virtual
Write Your Own Review
You're reviewing:Intelligent 500mA Smart Charger for 4.8V-12V NiMH NiCd Race RC Batteries Vapex

Brands

Component Shop
VP Racing
Leopard Hobby
VP Flight
Vapex-Tech
VP Airsoft
Giant Power
Minwa
GP Batteries
Warton Metals Limited
ACTion Electronics
Eneloop
Eneloop Pro
OUTDO (Huawei)
  • Best Seller
  • Latest Products
  • Featured Products
 
 
 
Intelligent 500mA Smart Charger for 4.8V-12V NiMH NiCd Race RC Batteries Vapex